If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
About the Author:
Read more about Procedures On Installing Profile Design Cobra Bars You Must Follow.
0 commentaires: